Skip to content

Free UK delivery on every order

Our web shop delivers to UK addresses only. Outside the UK? Where to buy

Product support

Manuals & Setup Guides

Step-by-step help for ViperSafe products: reset a TSA luggage lock, change your VS60 padlock code and set a new key safe code safely.

Choose your product

Setup, step by step

Read the full reset guide

Last updated

Setting a new code takes a couple of minutes once you know how. These guides cover the most common tasks for ViperSafe locks and key safes. Every product also comes with its own printed instructions – if they show a step differently for your model, follow the instructions supplied with your product.

Before you change any code

  • Keep it open. Only change a code with the lock open, or the key safe door open.
  • Write it down first. Note your new code before you set it, and keep it somewhere secure – never on or near the lock.
  • Choose well. Avoid obvious codes such as 0000, 1234 or a year of birth, and don't reuse a bank card PIN.
  • Test before you trust it. Try your new code several times before you rely on it.
  • Keep it safe. For security reasons, we can't recover forgotten codes.

How to reset a TSA luggage lock (VS51 and VS50)

If your lock is new, start from the factory code shown in the instructions supplied with it.

Step 1: Open the lock

Turn the four dials to the current code and release the cable from the lock body. Keep the lock open until you've finished.

Step 2: Enter reset mode

On the VS51, move the reset switch on the side of the lock body into the reset position – the tip of a pen can help. On the VS50, use the reset control shown in your instructions.

Step 3: Set your new code

While the lock is in reset mode, turn the dials to your new four-digit code. Check that each digit sits exactly in line with the marker.

Step 4: Save and test

Return the reset switch to its normal position to save your code. Scramble the dials, enter your new code and check that the lock opens. Repeat this a few times before you attach the lock to your luggage.

About the inspection indicator. If your lock's indicator is showing when you collect your bag (red on the VS51), airport security opened it with a Travel Sentry® master tool during an inspection. Follow your instructions to reset the indicator ready for your next journey.

How to reset your VS60 combination padlock

The VS60 has 10,000 possible codes – ten times as many as a 3-digit lock. Here's how to set your own.

Step 1: Open the padlock

Turn the dials to the current code – the factory code shown in your instructions, if the lock is new – and pull the shackle fully open.

Step 2: Enter reset mode

With the shackle open, put the padlock into reset mode exactly as shown in the instructions supplied with your VS60. Keep it in reset mode while you set your new code.

Step 3: Set your new code

Turn the four dials to your new code, lining each digit up precisely with the marker.

Step 4: Save and test

Take the padlock out of reset mode, as shown in your instructions, before you close the shackle. Scramble the dials, then open and close the lock several times with your new code before you use it on a locker, shed or gate.

If the new code doesn't work, try your previous code first. If the reset didn't fully engage, the lock may still be set to it.

Changing the code on your key safe (VSKL001 and VS300)

You'll need the key safe door open to change its code. If you can, set your own code before you fit the key safe to the wall.

  1. Open the key safe with the current code, and remove your keys while you work.
  2. Find the code-change mechanism on the inside of the door. Your instructions show where it is and how it works.
  3. Set your new code as shown in your instructions. On the VSKL001, get into the habit of pressing C before you enter a code – it clears any previous button presses.
  4. Test with the door open. Before closing the door, enter your new code and operate the opening mechanism to check that the latch releases. Then try a wrong code and check that it doesn't.
  5. Close and check again. Put your keys back, close the door, clear the keypad or scramble the digits, and open it once more with your new code.

Keeping your key safe secure

  • Change the code regularly, and whenever someone no longer needs access – after a guest's stay, at the end of a tenancy or when care arrangements change.
  • Share the code privately, and only with people who need it. Never include it in a public listing or social media post.
  • After closing the door, clear the keypad (VSKL001) or scramble the digits (VS300), so your code isn't left on display.
  • Keep the weather cover or lid closed, to protect the code area from rain and grime.

Fitting your key safe

  • Fit it to a solid wall, such as brick, stone or concrete, using the fixings supplied. The VSKL001 comes with four screws and four wall plugs, and the VS300 also includes fixings.
  • Choose a discreet spot that's easy to reach for the people who'll use it, but not obvious from the street.
  • Check for hidden cables and pipes before you drill.
  • If you're not confident drilling into masonry, use a qualified tradesperson.

Forgotten your code?

For security reasons, we can't recover forgotten codes or open locks on your behalf. If you know the current code but can't get a reset to work, email support@vslocks.com with your model number and a description of what's happening, and we'll help you through it.

GuidesChoosing a key safe, TSA locks explained and more

We're here to help

Still stuck?

If you know the current code but a reset won’t take, email us your model number and what’s happening – we’ll talk you through it.